Gently lift the pivot plate and look behind it. Basically, the printhead is in the tilt position and can't move forward to the print position. Let me know if you need more info on this. -Bill Bill Sprouse and 2 other Printers Specialists are ready to help you Ask your own question now Share this conversation If damaged replace. 7.If Problem persists,replace the following parts. this contact form
xerox came out with repair kit to drill out new holes and resecure the process drive if this is what your problem is. It takes a lot of time and effort to put these articles together. Epoxy back on, drilled hole through side frame and used longer screws to mount. I went to the link you suggested and tried the jumper to put the printer in manufacture mode.
The camshaft that we adjusted earlier that sits on the bottom of the machine drives this unit. Once everything is aligned reinstall the process drive mount. Also be sure to read as it may help with troubleshooting.JKhttp://rbswebs4u.com/phaser.html by endeavor27 on Jul 30, 2010 at 2:27pm Add comment Please sign in to comment 0 Sorry about the link
Xerox created a special process mount repair kit but the repair time is increased. Offered warranty repair for several major printer manufacturers. 39287937 Type Your Printers Question Here... The process drive unit is the gear assembly on the front right side of the printer with the clear plastic cover. Xerox Phaser 8560 Troubleshooting It would do nothing else except display the black screen.
I would take out the pivot plate and get it to a ready state. Xerox Phaser 8560 Printer Error 07 010 This gear pack is screwed into the frame via some plastic mounts. Release two tabs to pull the right cover away from the printer (1 tab near the power plug, the other tab near where you took off the control panel. If that doesnt help post back and I'll give you more info but that should cure it.
I have rebooted the printer with no resolution. There is very little space to remove objects from this area, so I recommend anyone else who experiences this to be patient and take your time removing any obstacles to avoid Xerox Phaser 8560 Error Codes List Put the cover off to the side and leave the control panel plugged in and on top of the machine about where it originally was.Remove the rear screw. 07 010 Xerox I removed the two top screws from the back and got lots of wiggle, but can't get them removed.
The cams are known to crack and move out of position on the shaft. weblink Make sure not to over tighten them as you can break the drive mounts as mentioned above. This can cause all sorts of problems including the 07,010.43 error. If you notice cracks then the camshaft will have to be replaced. Xerox Phaser 8560 Service Manual
So with the maintenance kit removed pull up on the pivot plate and with a flashlight check the back of the cams for cracks. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. I have restarted printer. http://ngogeeks.com/xerox-phaser/xerox-phaser-8560-error-code-39.php What should I 11/4/2016 11/4/2016 Ashik Computer just dropped siteapproximately 6 years old 11/4/2016 11/4/2016 Richard X Ask a Technician Get a Professional Answer. 100% Satisfaction Guaranteed. 48 Technicians are Online
Once out-of-the-way you can look down and see the printhead. Cleaning the printhead on the Phaser 7800> Phaser 8500/8550/8560 07,010.43 error code August 8th, 2012 at 1:31 pm This error pops up when the printhead in your printer cannot move back This part is the drum maintenance camshaft.
If it feels loose, the mounts are likely broken. Join our community for more solutions or to ask questions. Parts are thoroughly tested, inspected for damage & defects and guaranteed 100% fully functional. $15.00 Xerox 120E29160 Left Printhead Restraint MFG Part Number: 120E29160 Condition:Refurbished MFG:Xerox This Xerox Turn the Control Panel over and place it on top of the printer.
Notches on the gears and on the frame should help with alignment. Email Password ▶ Log in
The control panel should just drop out. Parts are thoroughly tested, inspected for damage & defects and guaranteed 100% fully functional. $35.00 Xerox 120E29150 Right Printhead Restraint MFG Part Number: 120E29150 Condition:Refurbished MFG:Xerox This Xerox Join & Ask a Question Need Help in Real-Time? So I guess I would tell you to pull out the pivot plate.
On the left you should see a big black plastic piece that blocks your view of the front of the printer. If everything prints then clean up the covers and feed rollers and you should be could to go. Start theprinter indiagnosticsmode and runidiags testExerciseHeater - togglePrintheadheaters tosoften the ink.Manualseparate thewiper andPrinthead. Please post when you are finished with the link.
© Copyright 2017 ngogeeks.com. All rights reserved.