Regarding reballing, yes, expensive equipment is used to achieve it... reflowing the cpu and gpu and replacing the thermal paste has worked every time for me. Then just after I shut the power off I pressed firmly down on the scalar chip, I believe that's what it is, the chip by the GPU under the heat shroud, Ive done the Xclamp method and it is still broken. Check This Out
But if you let it be reflowed by someone, you're just spending money you should shove towards a new 360. tomi_the_great on 2010-08-15 16:04:42 : reflow for 5-10 minutes with fan turned off works for me. I had it gone for a few seconds, but ever since it doesn't dissapear. Reflowed the solder on the CPU, got 0013 even faster.
This is more, or less, a temperature setting issue and will be resolved with a bit more practice. I had one today that was fixed by a reflow of the southbrige. And No offense but I think buying a XBOX 360 is pointless and getting it JTAGGED/RGHED/FLASHED is really expensive here.
Now, I'm running a 1 to 2 hour stress test on that system, and it's been about 15 minutes the system's been running and it's still going strong. I could have swore it was a 8, im sure thats what I used... If so, It'll be nice having someone else to compare notes with as there isnt much information about this stuff out there. Had a reballed GPU Xenon come back to me.
Reflowed CPU and the xbox is now stable. Ace08-13-2010, 10:33 AM*sigh*... Your browser will redirect to your requested content shortly. And speaking of cracked and weak solder joints, that's specifically why the Xbox 360 overheats so much and the GPU fails.
slingblade1170, Jan 28, 2014 Top #10 (You must log in or sign up to reply here.) Show Ignored Content Share This Page Tweet Log in with Facebook Your name or email Ace07-07-2010, 12:53 AMUpdate on the repair process for the store: I can tell you one thing - Xbox 360s with a Xenon motherboard suck. i noticed that overheat in GPU cause this 0102 error. TmEE08-14-2010, 03:53 PMseems you got your problem fixed :) a friend of mine needs only 1hour for full dump.
Collection Intro Intro: Comprehensive Xbox 360 RROD guideI decided to create this instructable due to the many misconceptions out there regarding the Red Ring Of Death in the XBOX 360, why TmEE06-30-2010, 04:17 AMEasier or not, it's not really the answer... I then proceeded to reflow the CPU, and 0013 came back almost as soon as I turned on the console! and to verify the reflow you have to do this sequence few tens of times : Turn X360 on, wait 10...15 minutes for it to heat up...
e-mail [email protected] espa on 2010-12-08 00:25:43 : Fixed over a hundred of these with no problems. his comment is here Xximod4uxX 33,277 views 34:06 Proper Fix XBox 360 RROD FULL VIDEO - Duration: 39:51. I have to admit I don't know much about the ball version.Yes, please note that the temp is in Celcius (all my resources are apparantly from overseas lol), and this correlates Loading...
Crazy weird. UPDATE: FreeBOOT image is built and is now being flashed to the Xbox 360. That one was given back to the store, but they let me keep the Zephyr system. this contact form The root cause of the RROD is the BGA processors and the lead free solder used to ... 2 Step 2: Why the towel fix works, but is badSo, given what
chinitosoccer06-19-2010, 02:56 PMWhat tools did you use? This Falcon 360 has the dual heatsink on the GPU, which works a lot better than the stupid single heatsink used on Xenon and Zephyr Xbox 360s. Now, I just keep getting constant errors every time I try to read from the damn NAND, but never at the same place and never the same errors, either.
xbox360repairdfw 34,509 views 8:42 XBOX 360 Reflow 0102 with ACHI IR PRO SC. I'll perform the mod and let you know how it turned out. After leaving the Xbox 360 on for 5 minutes completely stock, the GPU heatsink was so hot I could barely touch it. I reflowed the solder on both the GPU and scaler chip as the GPU could also be at fault and let the system run for about close to 6 hours without
Right now, NANDPro is writing to block 0x0001A1. Is a normal hair dryer enough to make the reflow? I think I will just get it reballed. navigate here Afterwards, you need to reflow the solder with a heat gun.
I've made 4 different NAND dumps, and here's how the results turned out: -First dump with second dump: do not match. -Third dump with first dump: do not match -Third dump I've done this on two different computers, and both give these constant errors, but every time I dump the NAND, I get different errors at different places. After another reflow of GPU still 0102. They should swap it over for you.I did that one time.
There are always dangers doing it but if your getting a new 360 then couldn't hurt too much if something goes wrong. I'm still stuck trying to get a proper dump. Not sure when that will be though as I can already tell the reattachment process is going to take a long time to perfect. the thing is, that the overheat happens only when the system goes past 85C (185F), and the PCB will flex earlier than that, and its the flexing of the PCB that
Someone explain this to me. Did you re-heat? if it cuts a track how to repair it? Oh, and I also forgot that I also secured the motherboards to the case with longer screws and washers under the motherboard, to ensure that the motherboard doesn't change shape again.
Published on Nov 17, 2011Hello this is one of my best fixes for 0102 red ring of death fixes!This have got me 4 working xbox that has lasted for 3-6 months It came back WITH THE SAME RED RING OF DEATH. With that, there's a risk that other solder joints will crack. HansonHacks 173,251 views 14:59 RROD EASY FIX XBOX 360 Red Ring of Death - Duration: 29:47.
But who am I.. I've already redid heatsinks thermal paste on both GPU and CPU, and it seems to work fine for about 10 min, then it goes back to this error. It was on a motherboard revision only available from Microsoft through RROD repairs of the original arcade model. Before when I plugged in the xbox I would get the 3 rrod right away, now that I've done all of these things it starts, it tries to boot and then
This is somewhat better on the chip itself since heat is not going on it directly thus reducing possible heat damage... Well, if the problem is not overheating, it could indeed be caused by cold solder joints, cracking, voids, etc. And I've compared my 3 dumps that match, and none of them were garbage.
© Copyright 2017 ngogeeks.com. All rights reserved.