WSA_QOS_EOBJLENGTH 11022 Invalid QoS object length. The requested name is valid and was found in the database, but it does not have the correct associated data being resolved for. If you are using a host table exclusively, you'll need to update it to add the destination hostname and address. Note: this error may also result if you are trying to send a multicast packet and the default gateway does not support multicast (check your interface configuration). http://ngogeeks.com/socket-error/windows-live-mail-error-id-0x800ccc0e-socket-error-10060-pop3.php
WinSock description: Same as Berkeley. In this case, the 2nd application will fail with WSAEADDRINUSE. This normally results if the peer application on the remote host is suddenly stopped, the host is rebooted, the host or remote network interface is disabled, or the remote host uses User suggestions: Did you enter a destination hostname?
I hope you find it useful! A connection attempt failed because the connected party did not properly respond after a period of time, or the established connection failed because the connected host has failed to respond. Developer suggestions: Always check the return value from a memory allocation to be sure it succeeded.
Occasionally the error code could have more variables in Wsaenotconn Error formatting .This further number and letter code are the location of the storage regions in which the instructions are stored WinSock description: Similar to Berkeley. A Windows Sockets implementation may have a limit on the number of applications that can use it simultaneously. Socket Error 10049 This documentation is archived and is not being maintained.
It can also be returned by setsockopt if an attempt is made to set SO_KEEPALIVE on a connection that has already failed. Socket Error 10038 You cannot reply to this topic 2 replies to this topic #1 Fibonacci One Members -Reputation: 284 Like Likes Like Posted 20 May 2004 - 08:47 PM I''m just trying WinSock functions: accept(), bind(), closesocket(), connect(), gethostbyaddr(), gethostbyname(), gethostname(), getpeername(), getprotobyname(), getprotobynumber(), getservbyname(), getservbyport(), getsockname(), getsockopt(), ioctlsocket(), listen(), recv(), recvfrom(), select(), send(), sendto(), setsockopt(), shutdown(), socket(), WSAAsyncGetHostByAddr(), WSAAsyncGetHostByName(), WSAAsyncGetProtoByName(), WSAAsyncGetProtoByNumber(), WSAAsyncGetServByName(), Typically, though, WinSock generates this error when it receives a "host unreachable" ICMP message from a router.
A couple functions that the v1.1 specification missed are WSASetLastError() and WSAUnhookBlockingHook(). Socket Error 10054 Connection Reset By Peer WinSock description: No equivalent in WinSock. The "address" it refers to is the remote socket name (protocol, port and address). Berkeley description: Some invalid argument was supplied (for example, specifying an invalid level to the setsockopt() function).
Some invalid argument was supplied (for example, specifying an invalid level to the setsockopt function). This unique Wsaenotconn Error error code features a numeric value and a practical description. Winsock Error Windows 7 WSA_QOS_TRAFFIC_CTRL_ERROR 11014 QoS traffic control error. What Is A Socket Error See also: WSAECONNABORTED, WSAECONNRESET, WSAENETRESET WSAETOOMANYREFS (10059) Too many references; can't splice Berkeley description: too many references to some kernel-level object; the associated resource has run out.
Berkeley description: A request to send or receive data was disallowed because the socket is not connected and (when sending on a datagram socket) no address was supplied. You can avoid making the mistake of trying to send on a socket after you've initiated a close, by keeping track of the socket state in your application (and checking it Article ID: W12629 Filename: Error 10057 WSAENOTCONN.txt File Created: 2010:02:17:11:58:31 Last Updated: 2001:03:01:15:12:38 Home TechHome Tech Support Forum Ordering About Us Contact Us Copyright©, Wilson WindowWare, Inc. Check This Out It’s the normal error message format utilized by Microsoft Windows and other Microsoft Windows compatible applications and driver manufacturers.
For example, the optional type SOCK_RAW might be selected in a socket call, and the implementation does not support SOCK_RAW sockets at all. Can indicate a service provider implementation error. An incorrect number of QoS FILTERSPECs were specified in the FLOWDESCRIPTOR. Socket Error Codes Linux Some implementations also return this error if sendto is called on a connected SOCK_DGRAM socket (for SOCK_STREAM sockets, the to parameter in sendto is ignored) although other implementations treat this as
All rights reserved. TCP/IP scenario: Most WinSock implementations use domain name system (DNS) protocol for hostname to address resolution, although a few use Network Information System (NIS). If I could find a good alternative to FSXfollow I would probably switch. http://ngogeeks.com/socket-error/wsa-error.php Thank you for your support!
Ran out of disk quota. This error is also returned if the service provider returned a version number other than 2.0. Ping the remote host you were connected to. AVSIM History Media Gallery Video Library Open Quick Navigation View New Content Sign In Use Facebook Use Twitter Need an account?
WSAESHUTDOWN 10058 Cannot send after socket shutdown. Detailed description: setsockopt(): WinSock generates this error if you try to set SO_KEEPALIVE but the connection has already been aborted (e.g. WinSock description: Same as Berkeley; the option is unknown or unsupported. Yes No Additional feedback? 1500 characters remaining Submit Skip this Thank you!
Berkeley description: An attempt was made to access a file in a way forbidden by its file access permissions. Note the British spelling (with an 'S' instead of a 'Z'). This usually means the local software knows no route to reach the remote host. See also: WSAECONNABORTED, WSAENETRESET, WSAETIMEDOUT WSAEDESTADDRREQ (10039) Destination address required.
Berkeley description: A connection abort was caused internal to your host machine. Note that this error is returned by the operating system, so the error number may change in future releases of Windows. Dialup box: Go to Control Panel/Internet/Remove autodial feature, and check on the CD. An invalid FILTERSPEC was found in the QoS provider-specific buffer.
WinSock functions: bind(), connect(), sendto(), socket(), FD_CONNECT See also: WSAEPROTOTYPE WSAEALREADY (10037) Operation already in progress. Berkeley description: The support for the socket type has not been configured into the system or no implementation for it exists. WinSock functions: Any function which allocates a new descriptor: accept(), listen(), & socket(). Berkeley description: A connect or send request failed because the connected party did not properly respond after a period of time. (The timeout period is dependent on the communication protocol.) WinSock
Debug(1) AddExtender("wwwsk34I.dll") ;This is where I get a VALUE=>13567456 socket=sOpen() ;This is where I get a status of VALUE=>1 or "@TRUE" status=sConnect(socket,"127.0.0.1", "daytime") ;This is where I get a err of Guest, the last post of this topic is over 60 days old and at this point you may not reply in this topic. WinSock functions: connect(), sendto(), FD_CONNECT WSAEDQUOT (10069) Disc quota exceeded.
© Copyright 2017 ngogeeks.com. All rights reserved.