These conditions are more likely to be indicated by the error WSAETIMEDOUT. copies what it can into your buffer) and fails the function. Since the buffering requirements for sending are less than for receiving datagrams, it's conceivable that you can send a datagram larger than you can receive. Users should check: That the appropriate Windows Sockets DLL file is in the current path. http://ngogeeks.com/socket-error/windows-live-mail-error-id-0x800ccc0e-socket-error-10060-pop3.php
WinSock functions: getsockopt(), setsockopt() Additional functions: Bad IP headers can cause routers and remote hosts to issue ICMP "parameter problem" messages, which result in a ENOPROTOOPT error on Berkeley-derived systems. It means that there is a blocking operation outstanding. How to NOT render a part of a document Does there exist a basis for the set of 2 x 2 matrices such that all basis elements are invertible In a WinSock description: Same as Berkeley, and then some.
The only time a WinSock might use this error--at least with a TCP/IP implementation of WinSock--it fails a function with other errors (for example, WSAETIMEDOUT). A name component or a name was too long. Error Description List
in the v1.1 WinSock specification. WSAECANCELLED 10103 Call has been canceled. Typically, though, Winsock generates WSAENETUNREACH when it receives a 'host unreachable' ICMP message from a router instead of WSAEHOSTUNREACH. Socket Error 11004 In this case, the WSAEBADF error might mean the same as a WSAENOTSOCK error.
WSA_QOS_EUNKOWNPSOBJ 11024 Unrecognized QoS object. Socket Error 10049 The call has been canceled. WSAEAFNOSUPPORT (10047) Address family not supported by protocol family. Too many links were encountered in translating a pathname.
Berkeley description: A request to send or receive data was disallowed because the socket is not connected and (when sending on a datagram socket) no address was supplied. Winsock Error 10061 At least one QoS reserve has arrived. If you are using a host table exclusively, you'll need to update it to add the destination hostname and address. WSAENETRESET 10052 Network dropped connection on reset.
Berkeley description: This is a temporary condition and later calls to the same routine may complete normally (also known as EAGAIN error in Berkeley Software Distribution version 4.3) WinSock description: Same WinSock functions:
WSA_QOS_EFLOWCOUNT 11023 Incorrect QoS flow count. navigate here WSA_QOS_RESERVED_PETYPE 11031 Reserved policy QoS element type. The current Windows Sockets implementation does not support the Windows Sockets specification version requested by the application. Does トイレ refer to the British "toilet" or the American "toilet"? Socket Error 10054 Connection Reset By Peer
However, there's little distinction between WSAEALREADY and WSAEINVAL since a WinSock DLL cannot tell the difference between an asynchronous operation that has been cancelled and one that was never valid. I just started and exited the IOC 3 times and got a different set of errors each time. If you have more than one WINSOCK DLL on your system, be sure the first one in the path is appropriate for the network subsystem currently loaded. Check This Out Winsock description: The Windows Sockets definition of this error is very different from Berkeley Sockets.
WSASYSCALLFAILURE 10107 System call failure. Socket Error 10061 Connection Refused Handle the request as a non-fatal error (if possible), since some WinSock's can legally fail the request. WinSock description: Same as Berkeley.
Lewis Muir Sent: Fri 4/24/2009 11:01 AM To: Jeff Hill Cc: 'Mark Clift'; [email protected] Subject: Re: Winsock error10004 On 4/24/09 11:42 AM, Jeff Hill wrote: >> * Strangely, the ioc's that If not, check with your Winsock vendor to see if they have a newer Winsock available. WinSock description: Same as Berkeley. Winsock Error 10054 Fix User suggestions: Try to ping the destination host, to see if you get the same results (chances are, you will).
The occurrence of an unlisted error can provide extra detail. If an application sends a UDP packet to a host/port that does not have a datagram socket "listening," the network system may respond by sending back an ICMP Port Unreachable packet This article provides advice that tells you the best way to successfully treat your Microsoft Windows Winsock Error 10004, Error -107 error messages both by hand and / or automatically. http://ngogeeks.com/socket-error/wsa-error.php We chose to go with the server code in this tutorial as there are more things to go wrong, as you would appreciate.
Check that no old Windows Sockets DLL files are being accessed. WSAESOCKTNOSUPPORT 10044 Socket type not supported. Check the destination address you are using. Best Regards, Mark Clift. ________________________________________ From: Mark Rivers [[email protected]] Sent: Saturday, 25 April 2009 4:36 AM To: J.
you tried to connect to the wrong destination host address the server application isn't running on the destination host the server application isn't listening on the right port. This error occurs if you specifically reference a protocol that isn't part of the address family you also reference. Berkeley description: A file descriptor argument was out of range, referred to no open file, or a read (write) request was made to a file that was only open for writing Additional functions: a generic description of the type of functions that can return this error, which may include functions other than those listed by the WinSock specification.
User suggestions: Chances are the network subsystem is misconfigured or inactive. Whether to handle it as a fatal error or non-fatal error depends on the application and the context, so it's up to you to decide. Note that this error occurs rarely, because a Winsock implementation cannot reliably detect hardware problems.WSAENETUNREACH (10051) Network is unreachable A socket operation was attempted to an unreachable network. WSAENOMORE 10102 No more results.
© Copyright 2017 ngogeeks.com. All rights reserved.