The error can occur when the local network system aborts a connection. On a datastream socket, the connection was reset. This could be due to an out of memory error or to an internal QoS provider error. Either can block the ports needed to make a successful FTP connection to the remote server. Source
Berkeley description: The support for the socket type has not been configured into the system or no implementation for it exists. Ping the remote host you were connected to. For example, the value given for the origin when positioning a file pointer (by means of a call to fseek) is before the beginning of the file. If that's the case, you should use them as SMTP relay server (smart host in Exchange terminology).
WSAEAFNOSUPPORT (10047) Address family not supported by protocol family. at first i should say i am not like you professional1- about SecureNAT : I read http://www.isaserver.org/tutorials/The_SecureNAT_Client.html and as i told you i have set the ISA invalid Ip as a WinSock functions: gethostbyaddr(), gethostbyname(), getprotobyname(), getprotobynumber(), getservbyname(), getservbyport(), WSAAsyncGetProtoByName(), WSAAsyncGetProtoByNumber(), WSAAsyncGetServByName(), WSAAsyncGetServByPort(), WSAAsyncGetHostByAddr(), WSAAsyncGetHostByName(), See also: WSAHOST_NOT_FOUND, WSANO_RECOVERY, WSATRY_AGAIN WSANO_RECOVERY (11003) This is a non-recoverable error Berkeley description: This is a If so, then the application might have had a problem resolving the name.
A broken pipe error occurs when the server knows it has a message but can't seem to use its internal data link to get the data out to the socket. Check your Winsock implementation documentation to be sure all necessary components are currently installed and configured correctly. With the connection close the number of bytes transferred in/out is also shown. Winsock Error 10061 These errors might be reported on any function that does network I/O (e.g.
If an application sends a UDP packet to a host/port that does not have a datagram socket "listening," the network system may respond by sending back an ICMP Port Unreachable packetUser 10060 Socket Error WinSock functions: gethostbyaddr(), gethostbyname(), WSAAsyncGetHostByAddr(), WSAAsyncGetHostByName(), WSAAsyncGetProtoByName(), WSAAsyncGetProtoByNumber(), WSAAsyncGetServByName(), WSAAsyncGetServByPort() Additional functions: It is strange that the asynchronous protocol and services functions can fail with this error, but the synchronous cannot. Developer suggestions: You need to be prepared to handle this error on any functions that reference blocking sockets, or any calls to blocking functions, if you allow the user to cancel On the server end, you could use a network system utility similar to BSD's "netstat -a" command to check that your server is running, and listening on the right port number.
When it occurs, it could indicate a serious failure of your network system (i.e. How To Fix Socket Error 10060 WinSock description: Same as Berkeley. If you are using a router, verify the router is up and running (check by pinging it and then ping an address outside of the router). If you still receive a 10060 error, the server may be trying to send a listing for a very large directory (with many thousands of files) causing the client to time-out
Berkeley description: The attempted operation is not supported for the type of object referenced. All rights reserved. Socket Error 10065 No Route To Host ERROR:> Can't connect to remote server. Socket Error 10061 Connection Refused About your two questions, I have a hard time figuring out what you are trying to achieve.
An invalid or inconsistent flowspec was found in the QOS structure. this contact form When it occurs, it could indicate a serious failure of your network system (i.e. Developer suggestions: If you don't detect it beforehand (e.g. the byte-order functions, htonl(), htons(), ntohl and ntohl(), cannot fail. Winsock Error 10060 Mdaemon
User suggestions: Do you have the WinSock DLL that supports the version of the WinSock specification required by the application? So, for example, you can expect this error if a WinSock implementation doesn't support socket type SOCK_RAW within the Internet address family (AF_INET). Not implemented: Name server does not perform specified operation. have a peek here By calling shutdown a partial close of a socket is requested, which is a signal that sending or receiving, or both have been discontinued.
The software caused a connection abort because there is no space on the socket's queue and the socket cannot receive further connections. Socket Error 10060 Connection Timed Out You could not make a connection because the target computer actively refused it. for hotmail.com of type Mail Xchg on Class INET add.FROM 192.168.136.76 to 22.214.171.124(hotmail.com)/DES=SMTP PORT ( here i don't understand anything)FROM 192.168.136.76 to 126.96.36.199(hotmail.com)/SRC=SMTP PORT ( here i don't understand anything)but i
For example, you can try to ping the server(s). Return code/valueDescription WSA_INVALID_HANDLE 6 Specified event object handle is invalid. An object with an invalid ObjectLength field was specified in the QoS provider-specific buffer. http://ngogeeks.com/socket-error/winsock-error-10064.php I just cant connect to the machine via any port because of that error message NO ROUTE TO HOST.
WSAENOTCONN 10057 Socket is not connected. WSAEDQUOT 10069 Disk quota exceeded. As we pointed out earlier, your application should be ready to encounter any error at any time. Do a traceroute to the destination to verify all routers along the connection path are operational.
a) i want to use worldclient also as a mdaemon web mail.what should i do first? Daniel.Winsock error codes0 (WSABASEERR) No Error10004 (WSAEINTR) Interrupted system call10009 (WSAEBADF) Bad file number10013 (WSAEACCES) Permission denied10014 (WSAEFAULT) Bad address10022 (WSAEINVAL) Invalid argument10024 (WSAEMFILE) Too many open files10035 (WSAEWOULDBLOCK) Operation would VirtualizationAdmin.com The essential Virtualization resource site for administrators. Berkeley description: Only one usage of each address is normally permitted.
WinSock description: Same as Berkeley. No more file handles are available, so no more files can be opened. This may indicate the file was deleted on the NFS server or some other catastrophic event occurred. See other suggestions under WSAECONNABORTED.
© Copyright 2017 ngogeeks.com. All rights reserved.