Replace Command Board N FAIL 01/92 The pattern stored within the microcomputer EEPROM is incorrect Initialize EEPROM O FAIL 01/93 Radio has conditions A and O P FAIL 01/94 Microcomputer It provides a means for the MCU to communicate with other hardware devices. The time now is 1:14 PM. Previous page Next page 1...333435363738394041 Also See for MOTOROLA HT-1000 Motorola MTX Series Service 66 pages Motorola HT 1000 series Theory/troubleshooting Manual 60 pages Motorola HT1000 Quick Reference Card 4 navigate here
If the leak occurs at the control top Register Help Remember Me? Specialized Test Equipment Vacuum Pump Kit, NLN9839 The vacuum pump kit includes a vacuum pump with gauge, and a vacuum hose. DIN and DIN* are the data lines in which the I and Q data words are transferred from the ABACUS. Reply With Quote 04-03-12,05:57 PM #11 aes View Profile View Forum Posts Member Join Date Dec 2011 Posts 55 Thanks 6 Thanked 22 Times in 11 Posts Rep Power 63 Reputation
Of course the "yy" in these examples will actually be the real error code. Pinpoint the problem(s) to one (or more) of the following areas:•housing•antenna bushing seal•controls seal•frequency switch, toggle, and on/off/volume control switch•main seal•battery contact and battery contact seal•keypad9. Most internal ADSIC functions are clocked by this ODC signal at a rate of 2.4 MHz; it is available as soon as power is supplied to the circuitry. As with the vacuum pump kit above, the NTN9279A adapter connects the pressure hose to the radio's casting.!C a u t i o n 8-6Miscellaneous Hardware Other items needed for testing
The Spectra radios report most problems detected during the self-check on power up. This includes setting the operational modes and parameters of the DSP. This is my third attempt at trying to put together a working XTL5000 as the first two that I bought were duds, so I don't want to do anything stupid to Fail 01/90 Reinstall the 50-pin (48) and 20-pin (47) compression connectors; they can only be inserted in one way.
Check SIU T Miscellaneous Error / Troubleshooting Codes: These codes were also found in the Advanced HHCH manual. Motorola Apx 7500 Error Codes When the clock output goes low, diode D104 conducts, allowing current to continue to ﬂow from ground through L119. This will ensure that no air goes through the seal.6. Up one level (Spectra index) Up two levels (Moto index) Back to Home Motorola SpectraFAIL and ERROR Codes Compiled By Robert W.
If you take a close look at the codes in the list, you can see the repeated pattern in the primary and secondary radio error codes. Xts5000 Fail 01/82 Now you might say its a trip to Motorola but i don't think so there has to be a way around it somewhere. Active Threads Forum Forum Home New Posts FAQ Calendar Forum Actions Mark Forums Read Quick Links Today's Posts View Site Leaders Forum Motorola Discussion ASTRO25 Radios XTL5000 O5 - Not recognizing Table 9–2.
The MCU programs many of the ADSIC operational features through the SPI interface. the tuning data i got out of the radio by the astro radio tuner program (all the softpot values) I'll be sending the radio off to an upgrade in firmware soon Motorola Xtl 5000 Error Codes Symptom Radio Dead; Display Does Not Turn On Radio Dead; Display Turns On No Receive Audio, or Receiver Does Not Unmute Table 9–1. Motorola Error Codes The pump creates a vacuum condition inside the radio, and the gauge monitors the radio for a stable vacuum reading; that is, checking for a properly sealed, watertight unit.
SSISERIALEXTALMODBMODAHC11/DSPInterfaceD0-D23BUSCONTROLA0-A15U405DSP56001 SCISERIAL EncryptionInterface To Secure BoardTo Controller BoardHostPortSystemClockGata ArrayLogicABACUS RxInterfaceTx D/AMAISDOGeneralPurpose I/OSpeakerD/AMicrophoneA/DSerialConfig.U406ADSIC ABACUSInterfaceTo/FromControllerBoardModulationOutU40332Kx8SRAMU404256Kx8FLASHU40232Kx8SRAMU40132Kx8SRAMHC11SPI BusMAEPF-25999-OFigure 6 Vocoder Board 6-3 The DSP sends the processed signal back to the ADSIC for D/A conversion. Motorola Xtl 2500 Error Codes If disassembly is necessary, refer to qualiﬁed service personnel and service shops capable of restoring the watertight integrity of the radio. Hand-Held Control Heads (HHC) display errors with their two seven-segment LED characters by first flashing "Er" or "FL", then the error code prefix, then the specific error code.
This detailed theory of operation will help isolate the problem to a particular component. It provides, among other things, the interface from the digital world of the DSP to the analog world. The microphone A/D converts the analog signal to a series of data words and stores them in internal registers. Motorola Xts 2500 Error Code 09/10 MHLN6918B is the newer one that supports both W series and O series.
Check SIUb. This is of paramount importance as irreparabledamage to the radio can result from service byunauthorized persons. Both the transmit and receive data paths between the DSP and ADSIC are through the DSP SSI port. http://ngogeeks.com/error-code/xfb-error-730.php MODA and MODB conﬁgure the memory map of the DSP when the DSP reset becomes active.
The data is available to the DSP through the ADSIC parallel registers. Had this same issue with our mobiles, easy fix. #4 (permalink) 12-09-2011, 11:41 AM fresnostatevb13 Member Join Date: Oct 2008 Location: Clovis, CA Posts: 21 That worked!
© Copyright 2017 ngogeeks.com. All rights reserved.