If this is occurring, the exit sensor on the fuser unit may not be working, failing to sense that the paper made it to the exit. Place the MFP on its right side. access cover will not close Fuser parts melted Toner not fused to the paper Blank page Black page Heavy background ... Most cost effective solution is to replace the fuser Lexmark Fuser Pricing Error 927 Main Fan Stalled, Cartridge Fan or RIP fan stalled, Power off and manually spin fan - it Check This Out
If the setting is not in your driver, you can download the correct Lexmark setup utility from the Lexmark Web site at www.lexmark.com. Remove the sensor and the attached cable, ... Lift the MFP up slightly, and disengage the lower hinge. 5. You will also see two white rollers and, underneath them, two white gears.
The user settings information is printed. 3-10 Service Manual manuals4you.comLexmark X342N | Service Manual - Page 71... ou.c y ...Lexmark X342N | Service Manual - Page 18...(3.87 x 6.38 in. Memory Optical photo conductor Printer Control Language Power-On Reset Power-On Self Test Personal ...
Carefully place the MFP on its back with the bottom of ... Machine type and model 7003-100 7003-050 7003-110 Description Lexmark X340 Lexmark X340n Lexmark X342n Parts catalog 7-1Lexmark X342N | Service Manual - Page 1447003-XXX Assembly 1: Covers 7-2 Service Manual manuals4you.comLexmark V 7-9 Fuser assembly, 220 V 7-9 Fuser assembly, 100 V 7-9 Laser/mirror print assembly, X340, X340n, X342n 7-9 Paper feed, rubber tires 7-11 Input #1 sensor ...cable 7-5 Flatbed cover Lexmark Fax Error E970 The thermistor provides feedback on the temperature of the fuser roller and when it fails, the fuser power is shut off and the fuser does not heat up.
To access the jam area: Open the upper front cover and remove the toner cartridge. Lexmark Error Codes Remove the exit guide assembly. Verify the cable is captured and out of the paper path. 4-24 Service Manual manuals4you.comLexmark X342N | Service Manual - Page 977003-XXX Input sensor #2 (manual feed) removal 1. 2. 3. When you remove the pen or pencil, the flag should pop back up freely.
The manufacturer is not responsible for safety in the event of use of unauthorized replacement parts. Fax Error Codes Ricoh Note: Improper fusing can result from incorrect media settings in the driver, or on the MFP. Veronica Casto Houston, TX It is nice to place anonline order & get to talk to an actual person. Main motor cable LVPS/HVPS Controller card Diagnostic information 2-25Lexmark X342N | Service Manual - Page 48....
Paper jammed in the ADF module. Paper exit guide assembly removal 1. Lexmark Fax Error Codes The heated roller is heated by a halogen lamp or in some cases a solid state ceramic heating element and is subject to failure. Error Code 700 Error In Fax Transmission Save this manual to your list of manuals Lexmark X342N manual table of contents:Lexmark X342N | Service Manual - Page 1Edition March 9, 2007 Lexmark™ X340, X340n, and X342n 7003-XXX •
Set the driver for multipage, or use a TWAIN driver. his comment is here Then pull the cartridge straight out towards you, as shown below. Disconnect the cover open switch at J13 on the controller card and extract the cable. 4. Back to Service Error Code List Source: Lexmark KnowledgeBase Home Page Technical Resources Lexmark Error Codes HP Error Codes Tech Support Blog HP Drivers Lexmark Drivers Terms & Conditions Product Lexmark Fax Error E-724
E-880 Failure to transmit training successfully in V17, V29, V27ter modulation schemes. • Select a lower ‘Max Speed’value under Fax Send settings.• Adjust ‘Transmit Level’.• Check line quality. viii Service Manual manuals4you...Lexmark X342N | Service Manual - Page 97003-XXX Huomautus laserlaitteesta Tämä kirjoitin on Yhdysvalloissa luokan I (1) laserlaitteiden DHHS 21 CFR Subchapter J -määrityksen mukainen ja muualla luokan Remove the paper tray. http://ngogeeks.com/error-code/wsh-error-codes.php See "Rear cover removal" on page 4-5. 2.
Fuser The fuser hot roll can cause toner deposits on the back of the paper if ...Lexmark X342N | Service Manual - Page 56... Fax Error Code E-713 Units/mach: ... types 1-4 print quality problems solving 2-34 print speed 1-1 printer taking offline ...33 S safety information ii-xi scan quality service checks 2-37 scanner quality...
Error 930 The wrong printhead is installed. Please try the request again. indicates a hot surface. http://ngogeeks.com/error-code/xfb-error-codes.php Remove the other screw from the bottom of the modem card. 4.
Remove the two screws (B) securing the fuser. 7. Repair information 4-29Lexmark X342N | Service Manual - Page 1027003-XXX Operator panel assembly removal 1. San Rafael, CA Great that you have that part in stock and thank you for your quick reply. No inkjet error codes available Error Code Error Message Solutions ERROR 20 ERROR 200 Input Paper Sensor was not triggered - Paper may be jammed at the sensor.
POR the MFP, and check each light for proper operation. Print quality will be diminished. Remove jammed media Error 90X Software Error Unrecoverable software error. A secondary error indication can be obtained by pressing an releasing a button.
The following table is an aid to find a problem with a cable connection. Load correct size Error 28 Input sensor not made after pick attempt. Remove lower right cover. Remove two screws (B) at the front of the top cover just behind the access door...Lexmark X342N | Service Manual - Page 847003-XXX Card cage removal 1.
Shop for Lexmark print cartridges Error 32 32 Wrong Print Cartridge installed The installed print cartridge is not supported by the Optra printer. Power printer off one to two minutes. These status bytes are designed to help isolate paper jams and paper feed problems in the base MFP. Part number : identifies the unique number that identifies this FRU.
See "Paper exit guide assembly removal" on page 4-31 for ... ERROR 23 Jam at the duplex unit. assembly. Download EC1 network daughtercard update.
© Copyright 2017 ngogeeks.com. All rights reserved.